10. Drying method: the left part of hot air drying oven + iron pipe under the oven heating for bis
　　10-1. Lower oven heating system for the most high-temperature 150 ℃ iron pipe
　　10-2. Heating speed - at room temperature to 150 ℃ is less than 15min
　　10-3 .. left me: the back blower on the heating system blowing smoke temperature for 120 ℃ adjustable air volume
　10-4 .. right cooling box: 8 4 "fan (wind speed can be adjusted yet scale)

11. Printing unit: 1 Unit
　　11-1. Network box -360 * 360 (mm), OR450 * 450mm
　　11-2. Printing trip-50-250mm
　　11-3. Printing speed of -60 ~ 300mm/sec
　　11-4. Printing transmission - even toothless screw + browser + servo motor shaft
　　11-5. Angle adjustment of ± 5 °
　　11-6. Scraper fixture (Article scratch size: T9 ~ 10mm, L170mm)
　　11-7. Cutting the level of adjustment: ± 2mm (adjusted scale 0.01mm)
　　11-8.刀下ink scraping pressure adjustment: 10mm (adjusted scale 0.1mm)
　　11-9. Cutting air pressure: MAX-4Kg / C ㎡
　　11-10. Off-grid distance (Snap Off) servo motor-driven, each lap automatically increased by
　　11-12. Churn away from 0 ~ 15mm (positioning accuracy of 0.001mm)
　　11-13.'s Lift-style dust cover
　　11-14. A variety of printing options

12. Positioning Block: 1 Unit
　　12-1. Positioning way: 90 ° cone PIN (repeat positioning accuracy of ± 0.01mm)
　　12-2. Dislocation (Shift) control: at the desktop, mining sub-setting chuck + hydraulic cylinder
　　12-3. Dislocation accuracy ± 0.01mm
　　12-4. Dislocation from the filthy 0 ~ 6mm

13. Tape / material with automatic separation, covered from top to bottom Automatic Feeding
　　13-1. Roll 3 "
　　13-2.'s Largest feed OD 300mm, width 160mm
　　13-3 aggregate diameter of the largest collection 300mm, width 160mm
　　13-4. Feed size 180mm (MAX)
　　13-5. Breathable belt feeding
　　13-6. A belt seized know
　　13-7. A vacuum suction disk seized know (material with no smoke alarms from the stands)

14. Electric control:
　　14-1. The whole machine PLC (Mitsubishi) control
　　14-2. PLC temperature control module
　　14-3 .. touch screen control-ying
　　14-4. A fault display
　　14-5. Have I, O show

Applicable to other industries:

MLCC, MLCI, NTC .. etc.
The line printing

1. Size: L3860 * 1320 * T1433

2. Machine weight: 1500KG

3. The use of power: 380V 60HZ 10KW (three-phase)

4. The use of air pressure: 5 ~ 7Kg/Cm2

5. Capacity: Each single-layer 7 / sec

6. Feeding method:
　6-1. Rod from top to bottom: bar + Ball Screw + motor + inverter + brake resistor
　6-2. About tower: chain + L Rail + motor + electronic brake + pneumatic cylinder

7. Conference side, Block: 1 Unit
　7-1 under the pressure cutting ceremony - gas hydraulic
　7-2. A retreat device

8. Bearer board: 64
　8-1: Size-L210 * W180 * H17 (mm)
　8-2 .. positioning hole - cone PIN-20O (MM) * 90 °
　8-3. Materials - aluminum alloy plate + surface treatment

9. Lamination Block: 1 Unit
　9-1. Lamination leveling, gas hydraulic (1000-10000Kg efforts
　9-2. Lamination temperature: 150 ℃ maximum
　9-3. Mining design under pressure
　9-4. Has a photoelectric detector security protection
　9-5.??agencies to retrofit